31 Various problems may arise during the selection process. The table below shows the typical causes and solutions. Trouble and solution of wire mesh breaks so that the wire mesh is torn. Wire mesh is worn and broken by abrasion The wire mesh is partially broken. (Always the same place breaks) The wire net wire breaks so that it breaks. There's a lot of clogging. I want to increase the processing capacity. I want to improve the efficiency of sieve. The wire mesh is mixed in. ・Secondary vibration of the net is conceivable. Regularly perform tension management to increase and tighten. ・Check that the tension of the net is uniform. ・In the case of square sieves, check that the middle net receiving rubber is not worn. ・Make the line diameter thicker. ※Attention: The processing capacity may be reduced due to a decrease in the opening rate. ・If the lower side of the net is worn, it is conceivable to wear by a tapping ball. Reduce the number of tapping balls or hit the entire sieve net evenly. Alternatively, consider setting up a protective network. ・If the processing material is concentrated, the input method is distributed. ・If the tapping ball is concentrated in a specific location, ensure that it hits the entire sieve net evenly. ・Check the processing material and environment. If the net is corroded, the material is changed. ・Reduce the supply. ・The wire diameter is narrowed to increase the opening rate. ※Attention: The strength of the wire mesh may decrease. ・Consider toncaps and tyrod wire mesh. ※Attention: The sifting accuracy may be poor. ・Consider measures to prevent clogging, such as tapping balls. ・When sieve a highly viscosity object, consider fluorinated resin coating. ・The wire diameter is narrowed to increase the opening rate. ※Attention: The strength of the wire mesh may decrease. ・Consider toncaps and tyrod wire mesh. ※Attention: The sifting accuracy may be poor. ・Consider the wire mesh for JIS Z8801 (test sieve). ・Consider flat top and arch clamp wire mesh. ・Consider a wire mesh with a thickness of the line diameter and a small gap. ・Increase the porosity (be careful of blindness). ・Perform periodic inspections to detect wear and tear and tear early. ・Consider magnetic materials such as KNM21 and dermaloy, and remove them with magnets. ・Consider the resin network. ・Consider the wire mesh. Problem cause and solution strength processing capacity sieve efficiency Strength processing capacity Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency Sieve efficiency S This drawing is a guide and may differ from the actual one. Net wire net 10 mm or more Particle size 1 mm to 10 mm Particle size 100 μm to 1 mm Particle size 100 μm or less Wet wire mesh net 4 16 4 18 18 9 12 8 9 18 9 18 9 18 9 18 9 18 Net wire net wire mesh Net wire mesh Net wire mesh Net wire mesh Net wire mesh Net wire mesh Net wire mesh Net wire mesh Net wire mesh Net 4 Net 4 Net wire mesh Net 4 Net 4 Net 4 Net 4 Net 4 Net 1 4 Net 4 Net 1 1 4 4 4 Net 1 4 Net 4 Net 4 Net 4 Net 4 Net 4 Net 4 4 Net 4 Net 4 Net
RkJQdWJsaXNoZXIy NDY3NTA=